FiberNetworksBlog

Fiber plc splitter  (Planar light wave circuit splitter) is a type of optical power management device that is fabricated using silica optical Waveguide technology. They are designed for FTTx Passive Optical Networks, CWDM, DWDM and optical cable TV System. We supply the Fiber plc splitter s including 1XN to 64 and 2XN to 64 types, they are with a wide range of working wavelength from 1260nm to 1620nm. The PLC splitter can be with optional various kinds of connectors and cable length, they feature compact size and very good optical performance. They provide a cost effective and space saving networking solution. They are key components in FTTH Networks and are responsible for distributing the signal from the central office to numbers of premises. With it’s compact size, these splitters can be utilised in in-ground and aerial pedestals as well as rack mount systems. Two types of planar light wave circuit (PLC) products--chips and modules--have been developed to serve the r...

A fiber optic connector terminates the end of a fiber optic cable and enables quicker connection and disconnection than splicing. It has to be aligned properly to the microscopic glass fibers completely in order to allocate for communication. In all, there are nearly 100 fiber optic connectors in the market, but only a few represent the majority of the market — st fiber optic connector , sc fiber optic connector, fc fiber optic connector etc. Next, some detail information about the above connectors will present to you. ST   Fiber Optic Connector ST refers to Straight Tip. The st fiber optic connector was developed by AT&T shortly after the arrival of the FC. They may be mistaken for one another, but ST uses a bayonet mount other than a screw thread. And you have to make sure SC  connectors  are seated properly owing to its spring-loaded structure. SC is mainly used in multimode  fiber optic  cable, campuses and buildings.

Fiber optic Pigtails is a fiber optic cable that has an optical connector using one conclusion and a length of exposed fiber on the other end. The connection side is used to link the equipment, as the other side is melted collectively with fiber optic wire. A Fiber optic Pigtails is single, short, usually tight-buffered. The technology of optical fiber fusion splicer can be used during the process which can lower the installation loss, that is, the end of the pigtail is stripped and combination spliced to one fiber of a multi-fiber trunk. Splicing of pigtails to each fiber in the trunk "break out" the multi-fiber cable into its component fibers for connection to the ending equipment. Fiber optic Pigtails can have female or male connectors. Although single-fiber solution exists, female fittings could be mounted in a patch panel, often in pairs. In this way, they can be linked to endpoints or other dietary fiber runs with patch fibers. In addition, male connectors ...

Armored fiber cable , just as the name indicates, is made with robust connectors and a stainless steel armored flexible tube inside the outer jacket, which acts as an effective protection against rodent, moisture and other issues that may cause the damage. Armored fiber cable serves as a member of the patch cable family, thus it retains all the features of standard patch cables. However, comparing with those common patch cables, Armored fiber cables are much stronger and tougher. For example, once stepped by an adult, standard patch cables may get damaged easily and fail to work normally. But things are totally different with armored patch cables which can withstand the strength and perform well. Besides, armored patch cables are rodent-resistant, that means as long as armored patch cables are employed in applications or systems, you don’t need to worry about rats biting the cables any longer. The Types of fiber optic armored cable There exist two types of fiber optic ...

Fiber optic plc splitter  (Planar light wave circuit splitter) is a type of optical power management device that is fabricated using silica optical Waveguide technology. They are designed for FTTx Passive Optical Networks, CWDM, DWDM and optical cable TV System. We supply the Fiber optic plc splitter s including 1XN to 64 and 2XN to 64 types, they are with a wide range of working wavelength from 1260nm to 1620nm. The PLC splitter can be with optional various kinds of connectors and cable length, they feature compact size and very good optical performance. They provide a cost effective and space saving networking solution. They are key components in FTTH Networks and are responsible for distributing the signal from the central office to numbers of premises. With it’s compact size, these splitters can be utilised in in-ground and aerial pedestals as well as rack mount systems. Two types of planar light wave circuit (PLC) products--chips and modules--have been developed to ...

Fiber optic armored cable , just as the name indicates, is made with robust connectors and a stainless steel armored flexible tube inside the outer jacket, which acts as an effective protection against rodent, moisture and other issues that may cause the damage.  Fiber optic armored cable serves as a member of the patch cable family, thus it retains all the features of standard patch cables. However, comparing with those common patch cables, Fiber optic armored cable s are much stronger and tougher. For example, once stepped by an adult, standard patch cables may get damaged easily and fail to work normally. But things are totally different with armored patch cables which can withstand the strength and perform well. Besides, armored patch cables are rodent-resistant, that means as long as armored patch cables are employed in applications or systems, you don’t need to worry about rats biting the cables any longer. The Types of fiber optic armored cable There exist...

A fiber optic connector terminates the end of a fiber optic cable and enables quicker connection and disconnection than splicing. It has to be aligned properly to the microscopic glass fibers completely in order to allocate for communication. In all, there are nearly 100 fiber optic connectors in the market, but only a few represent the majority of the market — FC fiber connector , LC fiber connector, SC fiber connector, ST fiber connector etc. Next, some detail information about the above connectors will present to you. FC Fiber Optic Connector: FC is short for Ferrule Connector. It is a round, threaded fiber optic connector that was designed by Nippon Telephone and Telegraph in Japan. The FC fiber connector is applied for single-mode optic fiber and polarization-maintaining optic fiber. The FC is a screw type connector with a 2.5mm ferrule, which was the first fiber optic connector to use a ceramic ferrule. However, FC is becoming less common and mostly replaced by ...

A fiber optic connector terminates the end of a fiber optic cable and enables quicker connection and disconnection than splicing. It has to be aligned properly to the microscopic glass fibers completely in order to allocate for communication. In all, there are nearly 100 fiber optic connectors in the market, but only a few represent the majority of the market —  Fiber SC  connector , fiber LC connector, fiber FC connector, fiber ST connector etc. Next, some detail information about the above connectors will present to you. Fiber sc connector SC stands for Subscriber Connector. SC, also called a square connector, was developed by Nippon Telegraph and Telephone in the market, slowly grew in popularity as manufacturing cost went down. Now Fiber sc connector is becoming increasingly popular in single mode fiber optic cable, analog CATV, GPON, GBIC. SC is a snap (push-pull coupling) connector with a 2.5mm ferrule diameter that operates on the standard IEC 61754-4. Th...

According to cable mode, patch cables can be divided into single-mode and multimode patch cable s. The word “mode” means the transmitting mode of the fiber optic light in the fiber optic cable core. Of all the differences between Singlemode Fiber Patch Cables and multimode patch cable s are the size of the fiber’s core and the associated attenuation or loss and bandwidth of the fiber. The multimode patch cable s are optical fibers with the core (25-200 microns) that supports several modes. Most multimode patch cables are an orange color. In addition, there is 10G OM3 and OM4 Multimode Patch Cable s which cable jacket are usually aqua. multimode patch cables are usually used in short distance, generally only a few kilometres, because their dispersion limits the frequency of digital signal transmission. Applications: Local Area Networks Telecommunication networks CATV Distribution Networks Point to Point Systems Wide Area Networks Industrial Applications

According cable mode, patch cables can be divided into multimode and single mode fiber cable s. The word “mode” means the transmitting mode of the fiber optic light in the fiber optic cable core. Of all the differences between single mode fiber cable s and Multimode Fiber Patch Cables are the size of the fiber’s core and the associated attenuation or loss and bandwidth of the fiber. The single mode fiber cable s are optical fibers with a small core (2-9 microns that supports one mode), which are most commonly used for transmitting data over long distances. They are usually used for connections over large areas, such as college campuses and cable television networks. And they have a higher bandwidth than multi mode cables to deliver up to twice the throughput. Most single mode fiber cable s are color-coded yellow. Applications: Local Area Networks Telecommunication networks CATV Distribution Networks Point to Point Systems Wide Area Networks Industrial Appli...

Wall mounted IP rated box es are designed to support fusion splicing or direct termination of the fibers. This modular enclosure provides cross-connect and interconnect capabilities for splicing and terminating outdoor cables & FTTH drop cables in fiber access network. Our Wall mounts fiber patch panels are made with 16-gauge mild steel with corrosion-resistant seven tank process powder coating to provide excellent protection for the inside fibers. IP rated box provides an extensive range of fiber management systems (FMS) fully compatible with industry grade fiber adapters. FTTH series wall mount fiber terminal box is designed to provide quick patching, storing fiber terminations. It is also used for Indoor/Outdoor application and medium size multi-dwelling units (MDU’s) for FTTx. Our IP rated box integrates three main functions of fiber splicing, cable winding & storing, and interface management. The enclosure adopts good quality metal sheets & surface el...

PLC Splitter (Planar light wave circuit splitter) is a type of optical power management device that is fabricated using silica optical Waveguide technology. They are designed for FTTx Passive Optical Networks, CWDM, DWDM and optical cable TV System. We supply the PLC splitter s including 1XN to 64 and 2XN to 64 types, they are with a wide range of working wavelength from 1260nm to 1620nm. The PLC splitter can be with optional various kinds of connectors and cable length, they feature compact size and very good optical performance. They provide a cost effective and space saving networking solution. They are key components in FTTH Networks and are responsible for distributing the signal from the central office to numbers of premises. With it’s compact size, these splitters can be utilised in in-ground and aerial pedestals as well as rack mount systems. Two types of planar light wave circuit (PLC) products--chips and modules--have been developed to serve the rapidly expanding...

Optical fiber  lc connector provides an extensive line of high-performance fiber optic connectors for termination of the end of an optic fiber cable and enables quicker connection and disconnection. The connectors mechanically couple and align the cores of fibers so that light can pass. Better connectors lose very little light due to reflection or misalignment of the fibers. LC ( Little Connector)is a small form fiber optic connector that uses a 1.25 mm ferrule, half the size of the SC. Otherwise, it's a standard ceramic ferrule connector, easily terminated with any adhesive. Optical fiber lc connector s are available in industry standard beige (multi mode), blue (single mode) and green (angle polish) colors, With its six-position tuning feature, the connector may be used to achieve unprecedented insertion loss performance by optimising the alignment of the fiber cores. Application: The Optical fiber lc connector is widely used in telecommunications networks, local...

Optical fiber connector provides an extensive line of high-performance fiber optic connectors for termination of the end of an optic fiber cable and enables quicker connection and disconnection. The Optical fiber connector s mechanically couple and align the cores of fibers so that light can pass. Better connectors lose very little light due to reflection or misalignment of the fibers. Features: High Precision Ceramic Ferrule High Precision Polymer housing Simplex or Duplex High Precision Nickel plated brass housing APC Green Polymer housing with 900μm and 3mm strain relief boot Low Insertion Loss Low Return Loss Ease of installation Low cost Reliability Low environmental sensitivity Ease of use A variety of Optical fiber connector s like SC, ST, LC, FC, MTRJ, SMA, DNP, SMI & SC-RJ are available but SC and LC connectors are the most common types of connectors on the market. Typical connectors are rated for 500–1,000 mating cycles. The main differences amo...

Fiber optic home network is also known Fiber-to-the-home (FTTH). Fiber optic home network the delivery of a communications signal over optical fiber from the operator's switching equipment all the way to a home or business, thereby replacing existing copper infrastructure such as telephone wires and coaxial-cable. Unisol Fiber optic home network  is the idea of bringing high-speed networking, digital television and telephone service to residences using fiber optic cables. Telecommunication companies developing Fiber optic home network technology plan to support 100+ Mbps bandwidth per home. They view fiber optic cabling as the best technology for high-speed, high-quality residential area networking, eventually replacing both telephone and cable TV lines. Costs to get Fiber optic home network services off the ground are high, but fibers to the home installations are steadily increasing around the world. UNISOL  communications s...

The IP Code reflects the degree of protection as "IP" followed by two numbers; the first digit shows the extent to which enclosure s  are protected against particles and protection to others from enclosed hazards.  Characteristics of IP 55 : Protection from dirt, dust, oil, and other non-corrosive material Protection from water, up to water projected by a nozzle against FTTH box from any direction Available in aluminium, and stainless steel Available in wall-mounted, free standing and Rack mounted box Custom with cutouts, insulation, hinges, latches, or locks The rating consists of the letters IP followed by 2 digits, the first digit stands for the level of protection that the enclosure provides against solid bodies, IP 55   =  First Digit - Solids The second digit describes the degree of protection of the equipment inside the enclosure against water. IP 55    =  Second Digit - Liquids

Direct burial cable is a kind of communications or transmissions power cable which is specially designed to be hidden under the ground without almost any extra covering, sheathing, or piping to protect it. Direct burial cable is a special type cable that is designed to be run in a funnel underground with no use of conduit to surround it. The electrical wires are encased in a thermoplastic case that seals out moisture and protects the wires within. Most Direct burial cable is built to unique tolerances to heat, wetness, conductivity, and soil level of acidity. Unlike standard telecommunications and power cables, which have only a thin coating of insulation and a waterproof outer cover, Direct burial cable involves multiple layers of heavy metallic-banded sheathing, heightened by heavy rubber masks, shock absorbing gel, covered thread-fortified waterproof tape, and stiffened by a heavy metal core. Direct burial cable is usually black with tagging to identify the natura...

Fiber optic pigtail is a fiber optic cable that has an optical connector using one conclusion and a length of exposed fiber on the other end. The connection side is used to link the equipment, as the other side is melted collectively with fiber optic wire. A Fiber optic pigtail is single, short, usually tight-buffered. The technology of optical fiber fusion splicer can be used during the process which can lower the installation loss, that is, the end of the pigtail is stripped and combination spliced to one fiber of a multi-fiber trunk. Splicing of pigtails to each fiber in the trunk "break out" the multi-fiber cable into its component fibers for connection to the ending equipment. Fiber optic pigtail can have female or male connectors. Although single-fiber solution exists, female fittings could be mounted in a patch panel, often in pairs. In this way, they can be linked to endpoints or other dietary fiber runs with patch fibers. In addition, male connectors can be...

Fiber Optic Patch cable used to connect one optical device to another for signal routing. Armored fiber optic patch cable s retain all the features of standard patch cords, but are much stronger. Armored fiber optic patch cables will not get damaged even if stepped by an adult and they are rodent-resistant. By using an Armored fiber optic patch cable you don't need to worry about rodents like rats that may bite the cables. Armored fiber optic patch cable s are strong; they are actually as flexible as standard fiber optic patch cords. Armored fiber optic patch cords are made a with the similar outer diameter to standard patch cords, make them both space saving and strong. What's more, they can be made with different jacket colors and jacket types such as OFNR etc. Armored fiber optic patch cords can be made with LC, SC, FC, ST, LC/APC, SC/APC, FC/APC and other types of connectors. UNISOL TM  can deliver customised Armored fiber optic patch cable ...

UNISOL TM   Ftth termination box es are designed to support fusion splicing or direct termination of the fibers. This modular enclosure provides cross-connect and interconnect capabilities for splicing and terminating outdoor cables & FTTH drop cables in fiber access network. Our Ftth termination box es are made with 16-gauge mild steel with corrosion-resistant seven tank process powder coating to provide excellent protection for the inside fibers. IP rated Ftth termination box es provides an extensive range of fiber management systems (FMS) fully compatible with industry grade fiber adapters. FTTH series wall mount fiber terminal box is designed to provide quick patching, storing fiber terminations. It is also used for Indoor/Outdoor application and medium size multi-dwelling units (MDU’s) for FTTx. Our IP rated Ftth termination box es integrates three main functions of fiber splicing, cable winding & storing, and interface management. The enclosure adop...

FTTH (Fiber to the Home) is the idea of bringing high-speed networking, digital television and telephone service to residences using fiber optic cables. Telecommunication companies developing FTTH technology plan to support 100+ Mbps bandwidth per home. They view fiber optic cabling as the best technology for high-speed, high-quality residential area networking, eventually replacing both telephone and cable TV lines. Costs to get FTTH services off the ground are high, but fibers to the home installations are steadily increasing around the world.  Application: Rack & Wall mount patch panel /LIU Fiber Optic Pigtails & Patch Cards Plc's & Splitters Connectors & Couplers UNISOL TM  communications specialise in providing various fiber network solutions based on clients unique. We are providing FTTH (Fiber To The Home) using GPON technology based on customer requirement. 

UNISOL’s wall mount interconnects enclosure provides a convenient convergence point for interconnect/cross connect or splicing in wall mount applications. The fiber patch panel features a well-engineered solution for fiber and cable management on both the ingress and egress openings of the enclosure. Robust steel construction ensures the highest level of protection for sensitive components inside the enclosure & aluminium casting hinges mounted from outside eliminate possible fiber pinch points when installing or servicing components within. Double hinged type single door is keyed differently to maintain security for the Network and Distribution sides of the termination fiber patch panel s. Unisol wall mount fiber patch panel adds an extra element of security and reliability to your network system. A multi port cable entries allow greater flexibility for integrating practically any network component. We offer a wide range of wall mount fiber patch panel s includin...

Nano DIN Rail  fiber optic patch panel is designed to support fusion splicing or direct termination of the fibers. Because of its compact and ruggedly designed case, it is suitable for industrial applications. The device includes a splice tray for fusion splicing. It is suitable for mounting in DIN Rail panels where there are space constraints inside PLC’s and also suitable for CCTV & surveillance applications. Din rail fiber optic patch panel is compact in size and can be mounted in a cabinet with other din rail equipment. Din Rail mount enclosures are suitable to mount in substation automation networks. Din rail mount fiber patch panel is used to provide a maximum number of fiber connections in a minimal footprint. DIN Rail fiber optic patch panel  is used in CCTV traffic monitoring, toll systems and environmental monitoring equipment where these can be secured in small wayside cabinet backplane or side panel. The patch panel can be loaded with a va...

UNISOL Micro Din Rail mounted Patch Panel is designed to support fusion splicing or direct termination of the fibers. Because of its compact and ruggedly designed case, it is suitable for industrial applications. The device includes a splice tray for fusion splicing. It is suitable for mounting in Din Rail mounted Patch Panel s where there are space constraints inside PLC’s and also suitable for CCTV & surveillance applications. The Unisol Micro panel is ideal for use in a wide range of industrial applications. The industrial design makes it highly suited for use in Machine Building, Transportation, Alternative Power Generation, Power Transmission & Distribution, and Oil & Gas markets, as well as more general use in the enterprise, buildings and other applications. Unisol developed the Nano, Micro, Miniature & also customization series Din Rail mounted Patch Panel s. These economical series of enclosures are the perfect choice for terminating fiber data cab...

standard Rack Mounted LIU (1U) UNISOL Fiber  Rack mounted LIU  provides cross-connect and interconnects capabilities for splicing & terminating optic fiber cables, pigtails in fiber access network. Rack mount fiber optic patch and splice enclosures in data cabinets are available pre-loaded with any connector interface required. These 19” 1U rack mount fiber patch panels are ideal for high-density LAN interconnect or cross-connect patching. These Fiber  Rack mounted LIU s are compatible with standard 19” and 23” equipment racks and are designed to accept wireworks, adapter strips and splice trays or distribution modules. Our rack mount panels are fabricated from 16-gauge mild steel with corrosion-resistant seven tank process powder coating to provide excellent protection for the inside fibers. The Fiber  Rack mounted LIU ears can also be adjusted to 3 different lengths from front to rear for even more flexibility.  Each side has large gr...

In conditions of different designs, fiber termination box can be classified into Wall mounted patch panel and rack mounted patch panel types. Wall mount fiber end of contract box is a perfect solution to be used in building access ports, telecommunication closets, main cross-connects, computer rooms and other managed environments. It is a suitable device for pre-connectarized cables, field unit installation of connectors and field splicing of pigtails. Wall mounted patch panel s make the inside fiber optic adapter panels, patch cables and pigtails realise the function of optical fiber distribution. And they are used for protecting fiber optic cables and connections of pigtails in fiber optic cabling and user terminal applications. The Wall mounted patch panel s are installed on the indoor wall with a terrace which can provide a flexible fiber management system for transiting external device cables t...

Din rail patch panel  |  Fiber rack mount patch panel  |  Mini rack mount   Description: Miniature Rack mounted patch panel is suitable for backbone fiber optic cable termination. Designed to support Fusion splicing or direct fiber termination. The device includes a splice tray for fusion splicing. It is compact in size & suitable for mounting in 19” Rack frame applications. Mini Rack mounted patch panel provides cross-connect and interconnects capabilities for splicing & terminating OFC cables, pigtails in fiber access network. Rack mounted patch panel in data cabinets are available pre-loaded with any connector interface required. These 19" rack mount panels are ideal for high-density LAN interconnect or cross-connect patching. Unisol’s Highly reliable Mini Rack mounted patch panel s offering user-friendly features that take fiber patching to next level. Mini Patch Panel can be loaded with a variety of adapters like ST, SC, FC a...

UNISOL 6 Port Nano Din Rail Mounted Box Enclosure is designed to support fusion splicing or direct termination of the fibers. Because of its compact and ruggedly designed case, it is suitable for industrial applications. Din rail mounted patch panel includes a splice tray for fusion splicing. Din Rail Mounted Box Enclosure is compact in size and can be mounted on the cabinet with other din rail equipment where there are space constraints inside PLC’s. Din Rail mount enclosures are suitable to mount in sub station automation networks and these can be used to provide a maximum number of fiber connections in a minimal footprint. Unisol developed the Nano, Micro, Miniature & also customization series Din Rail Mounted Box Enclosure s. These economical series of enclosures are the perfect choice for terminating fiber data cables where the expense of an outdoor enclosure is not desired. Din Rail Mounted Box Enclosure is used in CCTV traffic monitoring, toll systems and envi...

UNISOL Micro Din rail mounted LIU is designed to support fusion splicing or direct termination of the fibers. Because of its compact and ruggedly designed case, it is suitable for industrial applications. A device includes a splice tray for fusion splicing. Din rail mounted LIU is suitable for mounting in DIN Rail panels where there are space constraints inside PLC’s and also suitable for CCTV & surveillance applications. Din rail mounted LIU  is compact in size and can be mounted in a cabinet with other din rail equipment. Din Rail mount enclosures keep the patching in close proximity to the active equipment it serves and minimises cable management in the cabinet. Din rail mounted LIU solve many of the problems installers and integrator have faced when trying to adapt a conventional fiber optic patch panel for use in power, control, SCADA and industrial cabinets. Din rail mounted fiber patch panel is used in manufacturing industries to connect plant floor as...

UNISOL Din Rail mounted Patch panel is designed to support fusion splicing or direct termination of the fibers. Because of its compact and ruggedly designed case, it is suitable for industrial applications. The device includes a splice tray for fusion splicing. It is suitable for mounting in Din Rail mounted Patch panel s where there are space constraints inside PLC’s and also suitable for CCTV & surveillance applications. The Unisol Nano panel is ideal for use in a wide range of industrial applications. The industrial design makes it highly suited for use in Machine Building, Transportation, Alternative Power Generation, Power Transmission & Distribution, and Oil & Gas markets, as well as more general use in the enterprise, buildings and other applications. Unisol developed the Nano, Micro, Miniature & also customization series Din Rail mountable enclosures. These economical series of enclosures are the perfect choice for terminating fiber data cables where...

UNISOL 24 Port Mini Din Rail Mounted Enclosure is suitable for backbone fiber optic cable termination. Because of its compact and ruggedly designed case, it is suitable for industrial applications. Din rail mounted patch panel are designed to support fusion splicing or direct termination of the fibers. Din rail enclosure includes a splice tray for fusion splicing and It is suitable for mounting in DIN Rail panels where there is space constraint inside PLC’s. Din Rail Mounted Enclosure s are suitable to mount in substation automation networks and these can be used to provide a maximum 24 number of fiber connections in a minimal footprint. Unisol developed the Nano, Micro, Miniature & also customization series Din Rail Mounted Enclosure . These economical series of enclosures are the perfect choice for terminating fiber data cables where the expense of an outdoor enclosure is not desired. Din Rail mount fiber patch panel is used in CCTV traffic monitoring, toll systems an...

Micro Din rail mounted patch panel can support up to  6-12 ports when fully loaded with the adapters. patch panel can be loaded with a variety of adapters like ST, SC, FC and LC. Din rail enclosure is compact in size and can be mounted in a cabinet with other din rail equipment. Din Rail mount enclosures keep the patching in close proximity to the active equipment it serves and minimises cable management in the cabinet. The Unisol Nano Din rail mounted patch panel is ideal for use in a wide range of industrial applications. The industrial design makes it highly suited for use in Machine Building, Transportation, Alternative Power Generation, Power Transportation & Distribution and Oil & Gas markets as well as more general use in the enterprise, buildings and other applications. Din rail mounted patch panel s are used in CCTV traffic monitoring, toll systems and environmental monitoring equipment where these can be secured in small wayside ...

Fiber to the home (FTTH) is the delivery of a communications signal over optical fiber from the operator's switching equipment all the way to a home or business, thereby replacing existing copper infrastructure such as telephone wires and coaxial cable. 12 port FTTH wall patch panel. UNISOL 12 port FTTH wall patch panel /LIU are designed to support fusion splicing or direct termination of the fiber optic cable. This modular enclosure provides cross-connect and interconnect capabilities for splicing and terminating outdoor cables & FTTH drop cables in fiber access network. Our Wall patch panel s are made with 16-gauge mild steel with corrosion-resistant seven tank process powder coating to provide excellent protection for the inside fibers. IP rated Fiber enclosure provides an extensive range of fiber management systems (FMS) fully compatible with industry grade fiber adapters. FTTH series wall mount fiber terminal box is designed to provide quick patching, storing fib...

Fiber optic wall mount enclosure/LIU are designed to support fusion splicing or direct termination of the fibers. This modular enclosure provides cross-connect and interconnect capabilities for splicing and terminating outdoor cables & FTTH drop cables in fiber access network. Our Fiber optic wall  enclosures are made with 16-gauge mild steel with corrosion-resistant seven tank process powder coating to provide excellent protection for the inside fibers. IP rated Fiber optic wall  enclosure provides an extensive range of fiber management systems (FMS) fully compatible with industry grade fiber adapters. FTTH series wall mount fiber terminal box is designed to provide quick patching, storing fiber terminations. It is also used for Indoor/Outdoor application and medium size multi-dwelling units (MDU’s) for FTTx. Our IP rated Fiber optic wall  enclosure integrates three main functions of fiber splicing, cable winding & storing, and interface managemen...

Fiber to the house (FTTH), additionally referred to as fiber to the premises (FTTP), is that the installation and use of fiber from a central purpose on to individual buildings like residences, living accommodations buildings and businesses to supply unprecedented high-speed web access. FTTH dramatically increases the connection speeds available to computer users compared with technologies now used in most places. Wall mount panels /LIU are designed to support fusion splicing or direct termination of the fibers. This modular enclosure provides cross-connect and interconnect capabilities for splicing and terminating outdoor cables & FTTH drop cables in fiber access network. Our Wall mount panels are made with 16-gauge mild steel with corrosion-resistant seven tank process powder coating to provide excellent protection for the inside fibers. IP rated Fiber Wall mou...

IP rated Wall mounted cabinet provides an extensive range of fiber management systems (FMS) fully compatible with industry grade fiber adapters. IP rated  FTTH series wall mount fiber terminal box is designed to provide quick patching, storing fiber terminations. IP rated wall mounted cabinet s are protected from dust, oil, and other non-corrosive material. It is also used for Indoor/Outdoor application and medium size multi-dwelling units (MDU’s) for FTTx. IP rated Wall mounted cabinet integrates three main functions of fiber splicing, cable winding & storing, and interface management. The enclosure adopts good quality metal sheets & surface electrostatic spray technique, which is offering safety & good endurance performance. It is the ideal design for building & campus networking. Wall mounted cabinet /LIU are designed to support fusion splicing or direct termination of the fibers. This modular enclosure provides cross-connect and interconnect capa...